|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www..com DATA SHEET TFT COLOR LCD MODULE NL10276BC28-05D 36 cm (14.1 inches), 1024 x 768 pixels, 262,144 colors, LVDS interface, high luminance DESCRIPTION The NL10276BC28-05D is a TFT (thin film transistor) active-matrix color liquid crystal display (LCD) module comprising an amorphous silicon TFT attached to each signal electrode, a driving circuit, and a backlight. The NL10276BC28-05D has a built-in backlight and no inverters. The 36 cm (14.1 inch) diagonal display area contains 1024 x 768 pixels and can display 262,144 colors simultaneously. FEATURES * High luminance * Low reflection * LVDS interface (equivalent to the THC63LVDF64A of THine Electronics, Inc.) * 6-bit digital RGB signals * Incorporated edge-type backlight (two lamps) and lamp holder are replaceable APPLICATIONS * PC monitors www..com The information in this document is subject to change without notice. Please confirm the delivery specification before starting to design your system. Document No. EN0484EJ1V1DS00 (1st edition) Date Published January 2001 P CP(N) Printed in Japan DataSheet 4 U .com (c) 2000 www..com www..com 4U www..com NL10276BC28-05D STRUCTURE AND FUNCTION A color TFT (thin film transistor) LCD module is comprised of a TFT liquid crystal panel structure, LSIs for driving the TFT array, and a backlight assembly. The TFT panel structure is created by sandwiching liquid crystal material in the narrow gap between a TFT array glass substrate and a color filter glass substrate. After the driver LSIs are connected to the panel, the backlight assembly is attached to the back side of the panel. RGB (red, green, blue) data signals from a source system are modulated into a form suitable for active-matrix addressing by the onboard signal processor and sent to the driver LSIs, which in turn address the individual TFT cells. Acting as an electro-optical switch, each TFT cell regulates light transmission from the backlight assembly when activated by the data source. By regulating the amount of light passing through the array of red, green, and blue dots, color images are created with clarity. BLOCK DIAGRAM I/F LCD module IC Equivalent to THC63LVDF64A (THine) H-driver Controller D0+/- D1+/- D2+/- CK+/- 3072 dots V-driver www..com TFT LCD panel 768 lines GND FG DC/DC Converter Power supply for drivers H: 1024 x 3 (R, G, B) V: 768 VCC VHIGH VLOW VHIGH VLOW Backlight (Edge light type) Backlight (Edge light type) Note: GND is connected to FG (frame ground) inside the LCD module. 2 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U www..com NL10276BC28-05D CHARACTERISTICS (at room temperature) Item Display area Drive system Display colors Number of pixels Pixel arrangement Pixel pitch Module size Weight Contrast ratio Viewing angle (more than the contrast ratio of 10:1) Designed viewing direction 285.696 (H) x 214.272 (V) mm a-Si TFT active matrix 262,144 colors 1024 x 768 pixels RGB vertical stripe 0.279 (H) x 0.279 (V) mm 330.0 (H) x 255.0 (V) x 17.3 typ. (D) mm 1150 g (typ.) 150:1 (typ.) * * * * * Horizontal: 50 (typ., left side, right side) Vertical: 20 (typ., up side); 35 (typ., down side) Best contrast angle: down side 5 Wider viewing angle without image reversal: up side (12 o'clock) Optimum gray-scale (r = 2.2): perpendicular Description Color gamut Response time Luminance Signal system 40% (typ., at center, to NTSC) 11 ms (typ.), "white 100%" to "black 10%" 200 cd/m2 (typ., at IL = 6.1 mA rms/lamp) RGB 6-bit signals, synchronous signals (Hsync, Vsync), dot clock (CLK) LVDS interface (equivalent to the THC63LVDF64A, THine Electronics, Inc.) Supply voltage Backlight www..com 5 V (logic, LCD driving) Edge light type: Two cold cathode fluorescent lamps in a holder * Lamp holder: Type no.141 LHS08 9.5 W (typ., at IL = 6.1 mA rms/lamp) Power consumption Data Sheet EN0484EJ1V1DS00 3 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D GENERAL SPECIFICATIONS Item Module size Display area Description 330 0.5 (H) x 255.0 0.5 (V) x 18.5 max. (D) 285.696 (H) x 214.272 (V) [Diagonal display area: 36 cm (14.1 inches)] 1024 x 3 (H) x 768 (V) 0.093 (H) x 0.279 (V) 0.279 (H) x 0.279 (V) RGB (red, green, blue) vertical stripe 262,144 (RGB, 6 bit) 1150 (typ.), 1300 (max.) Unit mm mm Number of pixels Dot pitch Pixel pitch Pixel arrangement Display colors Weight pixel mm mm - color g ABSOLUTE MAXIMUM RATINGS Parameter Supply voltage Logic input voltage Lamp voltage Storage temp. Operating temp. Relative humidity (RH) Symbol VCC Vi VL TST TOP Note 2 95% Rating -0.3 to +6.0 -0.3 to VCC +0.3 2000 -20 to +60 0 to +50 Unit V V Vrms C C % Module surface Ta 40C - Note 1 Ta = 25C Remarks Absolute humidity www..com 85% % 40 < Ta 50C Note 2 Absolute humidity shall not exceed Ta = 50C, 85% relative humidity level. g/m3 Ta > 50C Notes: 1. Measured at the panel surface (including self-heat) 2. No condensation 4 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U www..com NL10276BC28-05D ELECTRICAL CHARACTERISTICS (1) Logic, LCD Driving Ta = 25C Parameter Supply voltage Ripple voltage Differential input "L" threshold voltage Differential input "H" threshold voltage Differential input voltage Common mode voltage Terminating resistor Supply current Symbol VCC VRP VTL Min. 4.75 - -100 Typ. 5.0 - - Max. 5.25 100 - Unit V mV mV for VCC VCM = 1.2 V VCM: Common mode voltage in LVDS driver Remarks - VTH - - +100 mV Vi VCM RT ICC 0.25 1.125 - - - 0.35 1.25 100 270 Note 0.45 1.375 - 600 V V mA RT = 100 RT = 100 - VCC = 5.0 V Note: Checker flag pattern (in EIAJ ED-2522) (2) Backlight Ta = 25C Parameter Lamp current Lamp voltage Symbol IL VL Min. 3.0 - Typ. 6.1 650 - - - Max. 6.5 - Unit mA rms V rms IL = 6.1 mA rms Remarks - Lamp turn-on voltage Note 1 Oscillator frequency www..com VS 1050 1550 Ft 53 - - 67 V rms Ta = 25C Ta = 0C Note 2 V rms KHz Notes: 1. When VS is less than the minimum value, lamps might not turn on. 2. Recommended value of Ft. * Ft is within the specification. * Ft = 1/4 th x (2n - 1) th: Hsync period n: a natural number (1, 2, 3...) If Ft is out of the recommended value, interference between Ft frequency and Hsync frequency may cause beat on the display. Data Sheet EN0484EJ1V1DS00 5 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D SUPPLY VOLTAGE SEQUENCE VCC ON VCC 0V 4.75 V 0.5 V tr < 80 ms t > 200 ms 0V Valid Signals* 10 < t < 35 ms 0 < t < 35 ms VCC OFF * The termination of the signal line is connected to resistance 100 . Notes: 1. Logic signals (synchronous signals and control signals) must be "0" voltage (V), when VCC is not applied. If input voltage to signal lines is higher than 0.3 V, the internal circuit will be damaged. 2. The supply voltage for input signals should be the same as VCC. 3. Turn on the backlight within the LCD operation period. When the backlight turns on before LCD operation or the LCD operation turns off before the backlight turns off, the display may momentarily become white. 4. When the power is off, keep whole signals at low level or high impedance. 5. This LCD module uses fuse as follows. Fuse www..com Type Name Productor VCC KAB2402162 MATSUO ELECTRIC Co., Ltd. Rating 24 V/16 A Before the power is designed, the fuses should be considered. The power capacity should be use more than 1.5 times of fuse rating. In case of small power capacity, the module should be evaluated enough. 6 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U www..com NL10276BC28-05D INTERFACE AND CONNECTOR PIN ASSIGNMENT (1) Interface Connector for Signal and Power CN1 Part no.: Supplier: Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol GND GND NC NC GND CK+ CK- GND D2+ D2- GND D1+ D1- Ground Pixel data Note LVDS differential data input Ground Pixel data Ground Pixel clock Note CLK for pixel data f = 65 MHz (typ.) (LVDS level) Note LVDS differential data input Nonconnection - Ground FI-SE20P-HF Japan Aviation Electronics Industry, Limited (JAE) Signal Type Note Function Adaptable socket: FI-SE20M GND D0 D0- GND GND VCC VCC www..com Ground Note Pixel data LVDS differential data input Ground Note +5.0 V power supply Supply +5.0 V 5% Note: GND is a signal ground for logic and LCD driving. GND is connected to FG (frame ground) inside the module. Remarks: Connect all pins (except 3 and 4) to avoid noise. Use 100 twisted-pair wires for the cable. CN1: Figure from socket view 20 19 ***** 2 1 CN2 20 1 Insert direction CN3 CN1 Data Sheet EN0484EJ1V1DS00 7 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D (2) Connector for Backlight Unit CN2, 3 Part no.: Supplier: Pin No. 1 2 3 Symbol VLOW NC VHIGH BHR-03VS-1 J.S.T. Trading Company, Ltd. Function Low-voltage terminal (The cable color is gray.) Nonconnection High-voltage terminal (The cable color is white.) Adaptable socket: SM02 (8.0)B-BHS-TB Note: VH and VL must be connected correctly. If they are not connected correctly, the user may get hurt and the module may break. CONNECTING THE THC63LVDF63A THC63LVDF63A (Thine) R0 R1 * * R5 G0 G1 * G5 * B0 TA0 TA1 * * TA5 TA6 TB0 * TB4 TB5 * * TC3 TC4 TC5 TC6 CLKIN NL10276BC28-05D IC Note 1 Equivalent to THC63LVDF64A (THine) Y0P Y0M Y1P Y1M D0+ D0- D1+ D1- Y2P Y2M D2+ D2- B5 Hsync Vsync DE CLK +3.3 V GND VCC (+5 V) CLKOUTP CLKOUTM CK+ CK- DC/DC Converter Notes: 1. 100 twisted pair 2. These signals should be kept in the range specified in INPUT SIGNAL TIMINGS. 3. VCCi = 3.3 V (LCD internal voltage) 8 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U Controller www..com * * * * * * * * * Note 3 www..com NL10276BC28-05D DISPLAY COLORS vs. INPUT DATA SIGNALS Data Signal (0: Low Level; 1: High Level) Display Colors R5 Basic colors Black Blue Red Magenta Green Cyan Yellow White Red gray-scale Black 0 0 1 1 0 0 1 1 0 0 dark bright 1 1 Red Green gray-scale Black 1 0 0 1 1 1 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R4 0 0 1 1 0 0 1 1 0 0 0 R3 0 0 1 1 0 0 1 1 0 0 0 R2 0 0 1 1 0 0 1 1 0 0 0 R1 0 0 1 1 0 0 1 1 0 0 1 R0 0 0 1 1 0 0 1 1 0 1 0 G5 0 0 0 0 1 1 1 1 0 0 0 G4 0 0 0 0 1 1 1 1 0 0 0 G3 0 0 0 0 1 1 1 1 0 0 0 G2 0 0 0 0 1 1 1 1 0 0 0 G1 0 0 0 0 1 1 1 1 0 0 0 G0 0 0 0 0 1 1 1 1 0 0 0 B5 0 1 0 1 0 1 0 1 0 0 0 B4 0 1 0 1 0 1 0 1 0 0 0 B3 0 1 0 1 0 1 0 1 0 0 0 B2 0 1 0 1 0 1 0 1 0 0 0 B1 0 1 0 1 0 1 0 1 0 0 0 B0 0 1 0 1 0 1 0 1 0 0 0 www..com dark bright 0 0 Green Blue gray-scale Black 0 0 0 dark bright 0 0 Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 1 1 1 0 1 1 1 0 1 Note: Colors are developed in combination with 6-bit signals (64 steps in gray-scale) of each primary red, green, and blue color. This process can result in up to 262,144 (64 x 64 x 64) colors. Data Sheet EN0484EJ1V1DS00 9 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D INPUT SIGNAL TIMINGS (1) Input Signal Specifications for the LCD Controller Parameter CLK Frequency Symbol 1/tC min. 60.0 - Rise, fall Duty Hsync Period tcrf tch/tC th 16.0 110 Display period Front porch Pulse width Back porch thd thf thp* thb *thp + thb Hsync-CLK timing CLK-Hsync timing DE-CLK timing CLK-DE timing Rise, fall Vsync Period ths thh tcs tch thrf, terf tv - 16.666 806 - - 0 12 2 86 Note 20.676 1344 1024 - - - - - 1780 - - - - - Note typ. 65.0 15.385 max. 68.0 - Unit MHz ns ns - - - 48.363 kHz (typ.) Remarks - s CLK CLK CLK CLK CLK CLK ns ns ns ns ns ms H - - - - - - - - - - 60.004 Hz (typ.) www..com 780 - tvd tvf tvp* tvb* *tvp + tvb 1 1 1 3 1 1 Note 768 - 3 - - - - - 36 36 38 - - H H H H H ns CLK ns ns ns Display period Front porch Pulse width Back porch - - - - - - - - - - Vsync-Hsync timing Hsync-Vsync timing Rise, fall DATA (R0-R5) (G0-G5) (B0-B5) DATA-CLK (setup) CLK-DATA (hold) tvs tvh tvrf tds tdh Notes: These values are in the timing regulation of the THC63LVDF64A (THine). The product equivalent of the THC63LVDF63A (THine) is recommended for the input of the LVDS transmitter. The timing regulation prescribes in the input of the LVDS transmitter. 10 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U www..com NL10276BC28-05D (2) Definition of Input Signal Timing for the LCD Controller tv tvp Vsync tvf tvb Display period Note tvd DE 1 2 3 4 768 www..com thp thb thpb Display period Note thf th thd DE Vsync tvh Hsync tvs Notes: 1. "Display period" does not exist as signals. 2. These values are in the output of THC63LVDF64A. (Refer to CONNECTING THE THC63LVDF63A) Data Sheet EN0484EJ1V1DS00 11 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D (3) Input Signal Timing Chart tc tch VIH CLK Vcci x 50% VIL tcrf tds DATA (R0 - R5) VIH (G0 - G5) Vcci x 50% VIL (B0 - B5) tdh Invalid Invalid tdrf tdrf teh VIH DE Vcci x 50% VIL tes teh tes terf terf CLK Vcci x 50% www..com thh ths VIH Vcci x 50% VIL thrf Hsync Hsync Vcci x 50% tvh VIH Vcci x 50% VIL tvs Vsync tvrf Note: VIH, VIL: Refer to the LVDS transmitter specifications. 12 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U www..com NL10276BC28-05D (4) DE Vsync tvp Hsync 1 2 ***** ***** tvb 768 H (fixed) ***** 1 ***** tvf DE ***** DATA Invalid D (x, 0) *** D (x, y) *** ***** Invalid D (x, 767) DE DATA Invalid D (0, y) D (1, y) *** D (x, y) *** Invalid D (1023, y) Hsync www..com ***** thp thb 1024 CLK (fixed) ***** 1 thf ***** 1 2 ***** CLK DE DATA Invalid D (0, y) D (1, y) ***D (1023, y) *** Invalid Note: These values are in the output of the THC63LVDF64A (refer to CONNECTING THE THC63LVDF63A). Data Sheet EN0484EJ1V1DS00 13 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D (5) Display Position of Input Data D (0, 0) D (0, 1) D (1, 0) D (1, 1) D (X, 0) D (X, 1) D (1022, 0) D (1022, 1) D (1023, 0) D (1023, 1) D (0, Y) D (1, Y) D (X, Y) D (1022, Y) D (1023, Y) D (0, 766) D (0, 767) D (1, 766) D (1, 767) D (X, 766) D (X, 767) D (1022, 766) D (1022, 767) D (1023, 766) D (1023, 767) www..com 14 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U www..com NL10276BC28-05D LVDS RECEIVER (1) Input Signal Specifications Parameter CLK frequency Bit 0 position Bit 1 position Bit 2 position Bit 3 position Bit 4 position Bit 5 position Bit 6 position Symbol TRCP TRIP1 TRIP0 TRIP6 TRIP5 TRIP4 TRIP3 TRIP2 Min. 14.71 -0.5 T/7-0.5 2T/7-0.5 3T/7-0.5 4T/7-0.5 5T/7-0.5 6T/7-0.5 Typ. T 0 T/7 2T/7 3T/7 4T/7 5T/7 6T/7 Max. 16.66 +0.5 T/7+0.5 2T/7+0.5 3T/7+0.5 4T/7+0.5 5T/7+0.5 6T/7+0.5 Unit ns ns ns ns ns ns ns ns Remarks T = 15.38 ns (2) Input Signal Timing Chart TRCP CK+ CK- The present cycle Next cycle D0+/- www..com R1' R0' G0 R5 R4 R3 R2 R1 G2' G1' B1 B0 G5 G4 G3 G2 R0 D1+/- G1 D2+/- B3' B2' DE Vsync Hsync B5 B4 B3 B2 TR1P1 TR1P0 TR1P6 TR1P5 TR1P4 TR1P3 TR1P2 Data Sheet EN0484EJ1V1DS00 15 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D OPTICAL CHARACTERISTICS (Ta = 25C; Notes 1, 2) Parameter Contrast ratio Luminance Luminance uniformity Symbol CR Lumax - At center "White" at center Maximum/Minimum Condition Min. 80 150 - Typ. 150 200 - Max. - - 1.30 Unit - cd/m - 2 Remark Note 3 - Note 4 Reference data (Ta = 25C; VCC = 5 V; VDDB = 12 V) Parameter Contrast ratio Symbol CR Condition Best contrast angle, X = 0, Y = -5, at center To NTSC, at center CR > 10, Y = 0 CR > 10, Y = 0 CR > 10, X = 0 CR > 10, X = 0 White to black Black to white Min. - Typ. 300 Max. - Unit - Remark Note 3 Color gamut Viewing angle range Horizontal C 35 40 40 15 25 - - 40 50 50 20 35 11 40 - - - - - 25 80 % deg. deg. deg. deg. ms Note 2 Note 5 X+ X- Vertical Y+ Y- Response time ton toff Note 6 Notes: 1. The luminance is measured after the module has been working for 20 minutes, with all pixels in white. Typical value is measured after luminance saturation. www..com 1 Photodetector (TOPCON BM-5A) 50 cm LCD 2. Viewing angle is x = 0, y = 0 3. The contrast ratio is calculated by using the following formula. Luminance with all pixels in white Luminance with all pixels in black Contrast ratio (CR) = The luminance is measured in a darkroom. 16 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U www..com NL10276BC28-05D 4. Luminance uniformity is calculated using the following formula. Luminance uniformity = Maximum Luminance Minimum Luminance 171 512 853 Line 1 3 4 5 2 128 384 640 Column 5. Definitions of viewing angles are as follows. Normal X- Left 12 o'clock Y- Y+ X+ Upper Lower Right 6. Definition of response time is as follows. www..com 100% 90% Luminance White 10% 0% ton toff Black Time Data Sheet EN0484EJ1V1DS00 17 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D RELIABILITY TESTS Test Item High temperature/humidity operation Note 1 Test Condition 50 2C, 85% relative humidity 240 hours Display data is black. <1> 0C 3C ... 1 hour 55C 3C ... 1 hour <2> 50 cycles, 4 hours/cycle <3> Display data is black. <1> -20C 3C ... 30 minutes 60C 3C ... 30 minutes <2> 100 cycles <3> Temperature transition time within 5 minutes <1> 5-100 Hz, 19.6 m/s2 (2G) 1 minute/cycle X, Y, Z direction <2> 50 times each direction <1> 294 m/s2 (30 G), 11 ms X, Y, Z direction <2> 3 times each direction 150 pF, 150 , 10 kV 9 places on a panel 10 times each place at one-second intervals 15 kinds of dust (JIS Z 8901) Hourly 15 seconds stir, 8 times repeat Heat cycle (operation) Note 1 Thermal shock (nonoperation) Note 1 Vibration (nonoperation) Notes 1, 2 Mechanical shock (nonoperation) Notes 1, 2 ESD (operation) Notes 1, 3 Dust (operation) Note 1 Notes: 1. Display function is checked by the same condition as the LCD module outgoing inspection. 2. Physical damage. 3. Discharge points are shown in the figure below. www..com 18 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U www..com NL10276BC28-05D GENERAL CAUTIONS The figures and statements below are very important. Please be sure you understand their contents completely. This mark indicates that you will get hurt and/or the module will be damaged if you make a mistake in operation. CAUTION This mark indicates that you will get an electric shock if you make a mistake in operation. This mark indicates that you will get hurt if you make a mistake in opration. CAUTION Do not touch an inverter, on which there is a caution label, while the LCD module is in operation, because of dangerous high voltage. (1) Caution when taking out the module a) Pick up the pouch only, when removing the module from a carrier box. (2) Cautions for handling the module a) As electrostatic discharges may break the LCD module, handle the LCD module with care against electrostatic discharges. b) c) As the LCD panel and backlight element are made from fragile glass material, impact and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. www..com d) Do not pull the interface connectors in or out while the LCD module is operating. e) Put the module display side down on a flat horizontal plane. f) Handle connectors and cables with care. lost, the LCD panel will be damaged. h) The torque for mounting screws should never exceed 0.392 N*m (4 kgf*cm). i) Don't push or rub the surface of LCD modules. If you do so, scratches or rubbing marks may be left on the surface of the modules. (3) Cautions regarding atmosphere a) Dew-drop atmosphere should be avoided. b) Do not store and/or operate the LCD module in a high-temperature and/or high-humidity atmosphere. Storage in an anti-static pouch at room temperature is recommended. c) This module uses a cold cathode fluorescent lamp. Therefore, the lifetime of the lamp is shortened if the module is operated in a low-temperature environment. d) Do not operate the LCD module in a high magnetic field. g) When the module is operating, do not lose the CLK, Hsync, or Vsync signal. If any one of these signals is Data Sheet EN0484EJ1V1DS00 19 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D (4) Cautions about module characteristics a) Do not apply a fixed-pattern data signal for a long time to the module. It may cause image sticking. Please use screen savers if the display pattern is fixed for a long time. b) This module has retardation film, which may cause variation in the color hue at different viewing angles. Nonuniformity may appear on the screen during high-temperature operation. c) A light vertical stripe may be observed, depending on the display pattern. This is neither a defect nor a malfunction. d) Noise from the inverter circuit may be observed in the luminance control mode. This is neither a defect nor a malfunction. (5) Other cautions a) Do not disassemble and/or reassemble the LCD module. b) Do not readjust variable resistors or switches in the module. c) When returning the module for repair, etc., please pack the module properly to avoid damage. recommend using the original shipping packages. The liquid crystal display has the following specific characteristics. These are neither defects nor malfunctions. The optical characteristics of this module may be affected by the ambient temperature. This module has a cold cathode tube for backlight. Optical characteristics, like luminance or uniformity, will change over time. Uneven brightness and/or small spots may be observed, depending on different display patterns. We www..com 20 Data Sheet EN0484EJ1V1DS00 DataSheet 4 U .com www..com www..com 4U 4 - 3.5 (5) (7.14) (9.5) (32) ACTIVE AREA CENTER 219 0.3 (BEZEL OPENING) 255 0.5 (214.27) (ACTIVE AREA) 200 0.3 200 0.3 (10.8) (13) (80) (13) (94) (13) (30) (72) (55) (13) (20) Inverter Notes: 1. Tolerance of the dimensions not shown is 0.5 mm. 2. The torque on a mounting screw should never exceed 0.392 N*m (4 Kgf*cm). MAX. 19 (16.2) DataSheet 4 U .com (4.5) Data Sheet EN0484EJ1V1DS00 www..com OUTLINE DRAWING: Front View (Unit: mm) 330 0.5 320 0.3 290.4 0.3 (BEZEL OPENING) (285.696) (ACTIVE AREA) MAX. 18.5 www..com NL10276BC28-05D www..com www..com 4U 21 11.2 10.6 1 20 52 24 48 28 5 37 54 8 1 120.5 ( 8) 30 0.4 0.2 4.1 2.7 0.1 DEPTH 6 a: Insulation sheet (PET, t0. 1) 20 32.2 12 8 6 23 101.5 0.2 100 150 120 11 7.3 0.2 5 30 23 10.2 A1009A2011001 3 12 6 86 28 5 11.2 10.6 1 DataSheet 4 U .com www..com www..com 4U www..com 22 11.3 103.3 FPC MAX. 18.5 18.3 1 TYP17.3 3.4 0.3 OUTLINE DRAWING: Rear View (Unit: mm) 2.7 0.3 www..com 9 Data Sheet EN0484EJ1V1DS00 5.1 CN1 10.2 1 9 NL10276BC28-05D Material Information Light guide: > PMMA < 260 1 www..com NL10276BC28-05D MEMO www..com Data Sheet EN0484EJ1V1DS00 23 www..com www..com 4U DataSheet 4 U .com www..com NL10276BC28-05D No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its e l e c t r o n i c components, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC electronic component, customers must incorporate sufficient safety measures in its design, such as redundancy, firecontainment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard," "Special," and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific a p p l i c a t i o n . T h e r e c o m m e n d e d applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical e q u i p m e n t ( n o t specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majorityowned subsidiaries. (2) "NEC electronic component products" means any electronic component product developed or manufactured by or for NEC (as defined above). DE0202 www..com DataSheet 4 U .com www..com www..com 4U |
Price & Availability of NL10276BC2805D |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |